We look into the details of installing a new faucet in the kitchen. Installation in the countertop and connection to the water supply system. How to ensure long-term operation without leaks.
1. Before starting work
- Firstly, it is necessary to turn off the water to avoid possible flooding;
- Open the tap to remove any remaining water;
- Study the passport for a new kitchen faucet made at moscowmebel.com or another factory.
2. Preparation
To replace, we will need the following materials and tools:
- Adjustable wrench (alternative – wrench);
- Two types of screwdrivers - flat and Phillips;
- Sandpaper;
- Flashlight;
- A container for draining water when replacing the siphon;
- New mixer.
If the kitchen sink model is removable, it is advisable to remove it. This will make it easier to dismantle the old product and install a new one.
We tighten the chrome siphon for the kitchen sink with an adjustable wrench.
If the old mixer belongs to the economy class, it is better to replace the soft hoses that connect the product and the water supply.
3. Dismantling
Before starting dismantling, turn off the water to the bathroom to prevent flooding.
Stages:
- We find the connection point with the pipes of the water supply system.
- We fix the place where the product is attached to the sink;
- If the sink is overhead, we dismantle it;
- Using an adjustable wrench, remove the soft tubes and pour the water into a prepared container.
- Remove the siphon part (bottom).
- We dismantle and rotate the sink so as to provide maximum convenient access to the connection point.
- Loosen the nut and other fasteners using an adjustable wrench, then remove the threaded pins with a screwdriver. To prevent the product from falling, control its position.
- We remove the special clamp, flexible hoses and mixer. We pull out the hoses through the mounting hole.
4. Installation
The day before, you should check the condition of the mounting hole. If dirt has accumulated in it, it must be removed.
Parts necessary for correct installation.
Before starting installation, install the hoses (supply to the water supply).
Stages:
1. We fix a special gasket (ring) on the base in the provided groove. This procedure will allow you to create a sealed system.
2. We stretch the hoses and then turn the sink over to its original position, holding the mixer. Check the position of the gasket - it should remain in place.
3. Install the seal and pressure plate (they must have the same shape).
4. Screw in special pins (threaded).
Reliable fastening due to threaded pins.
5. Use an adjustable wrench to tighten the mounting nuts.
If the nuts are not tightened properly, the faucet will constantly rotate.
5. Launch
- Check the four connections;
- After making sure that everything is in order, close the tap and turn on the water;
- Check the cold and hot water supply alternately to ensure there is no risk of leakage.
Photo: 3.bp.blogspot.com, dushik.com.ua, gidroguru.com, gor-servis.ru, i.minplastan-sale.ru, i.ytimg.com, lentaregion.ru, rmnt.ru, repair build.rf, o-vannoy.ru, small-house.ru, veles.msk.ru
The time comes and many owners of apartments and private houses are faced with the question of how to change the faucet in the kitchen. There can be many reasons, and first of all it is worth finding out whether it is possible to replace the faucet in the kitchen with your own hands, without involving a professional plumber in solving the problem.
It is worth saying that in the process of replacing a faucet in the kitchen, there is nothing complicated, you just need to follow a certain sequence of actions. And first of all, you should choose a device that will be most convenient and suitable for the style of your kitchen.
Faucet selection
The question of choosing a mixer is not as simple as it might seem at first glance. Currently, their range on the market is represented by dozens of companies, hundreds of models and thousands of price options. Therefore, huge shelves and display cases can cause confusion.
Tip: The first step to take before you decide to change your kitchen faucet is to choose a device before visiting the store. And our portal is ready to provide you with all the necessary photo and video materials with which you will purchase a high-quality and functional device.
Selecting a mixer depending on the internal device
- . A simple and familiar design from childhood: a spout located between two faucet axle boxes. The water supply is regulated using valves.
This design, although it has a relatively low price, has ceased to be in great demand. The fact is that individual components, in particular gaskets, are short-lived.
- . Popular with most modern buyers. And this popularity can be explained by the fact that the desired water temperature and water pressure can be set using one movement of the hand. Or an elbow, or a little finger.
- . Stylish, modern and comfortable design. When you put your hands near the sensor, which is built into either the sink or the body, water flows. You will have to pay decent money for such an electronic device. Therefore, these products occupy a modest market segment.
Faucet spout is an important factor
Next, you need to resolve the issue related to the height of the mixer spout. If it is high, then as a result of strong pressure, water can splash in all directions. If the spout is too low, it is inconvenient to wash large dishes. Therefore, it is worth choosing something in between.
It is important that the faucet is matched with a sink that has adequate dimensions. If you have doubts about your choice, you should give preference to those manufacturers who comprehensively solve this problem. A complete set, which includes a faucet, a sink and, of course, additional accessories, will help resolve this dilemma.
Perhaps you will pay attention to the possibility of using a modern kitchen assistant - a mixer with a pull-out spout. In various models, the spout can be removed from the socket by 60-120 cm. Use modern materials in the manufacture of hoses allows us to obtain a high-quality, durable and hygienic kitchen device.
Nozzle design
The nozzle design can be made in two versions.
- The usual aerator at the end, which is familiar to everyone.
- Shower head operating in two modes: aerated jet and shower. Using the “shower” mode will allow, for example, to wash berries or herbs quite carefully without damaging them. Well, and, of course, caring for the sink will be easier.
Materials for kitchen faucets
The service life of any device is determined by the material from which it is made. Currently, faucets are made from metal, plastic, as well as stone-style kitchen faucets.
- Metal alloys.
The production of mixers that have a budget price category is made from an alloy of aluminum with silicon, the so-called silumin. These devices are not particularly aesthetically pleasing and cannot boast of outstanding durability.
Brass and bronze are metals that have an excellent recommendation in the market. Durable, durable, water-neutral devices made from these materials are durable and long lasting. And they can be called the best kitchen faucets.
- Plastic.
Inexpensive, high-tech material that can adapt to the needs of any kind. Lightweight and durable material, chemically neutral to water.
It has low thermal conductivity, which is important in case of strong heating of the mixer parts. But still inferior to metals in terms of service life.
- Stone kitchen faucet.
Stone-effect kitchen faucets represent a new direction in the kitchen interior. Such mixers are produced by casting, and if used fake diamond, then an object can be cast in any shape. Among these items is a faucet, which has unique decorative characteristics.
A stone faucet can have almost any color, but neutral ones are more popular: black, graphite, white. They fit perfectly with most existing sinks. Among the advantages of stone-look faucets is the ability to take any, even the most fantastic, shapes.
Correct installation of the faucet in the kitchen is an important factor in the quality and durability of the service of this plumbing fixture. 
Similar articles:
How to choose a quality faucet
There are several types of mixers. The simplest are valve products. They are inexpensive and can be repaired. Disadvantage: more frequent leaks.
The optimal solution would be to install single lever mixer in the kitchen. This device is easy to use. To adjust the water pressure and temperature, only one lever is used.
When using two-valve mixers, you have to open two taps.
New products in the construction industry include sensor mixers. They work automatically when you reach out to them.
Preparing tools and materials for work
High-quality installation of a faucet in the kitchen is impossible without the appropriate tools and Supplies. For work we will need:
- mixer;
- adjustable wrench and screwdrivers;
- spanners;
- sandpaper;
- pliers;
- flashlight;
- small capacity;
- sealant;
- fasteners;
- rags.
When installing the mixer in the table you will also need:
- drill;
- electric jigsaw;
- marker.
If it is necessary to replace an old faucet in the kitchen, then the flexible hoses that supply water to the plumbing fixture are also replaced.
Work to prepare the crane installation site involves taking into account a number of features:
- location of drainage elements;
- distance from the wall to the mixer;
- diameter of the tap hole;
- type and size of sink.
It is better to remove the removable sink. This will make it easier to implement reliable installation mixer
Dismantling the old tap
In most cases, the process of installing a faucet in the kitchen consists of two stages:
- dismantling a faulty hot and cold water tap;
- installation of a new product.
First, how to remove the old faucet. This process involves performing the following sequential actions:
- turning off the water supply system;
- opening the tap (you need to drain all the water);
- determining the connection point of the mixer with the water supply and sink;
- disconnecting a flexible hose from the water supply network;
- drain the remaining water into a container;
- unscrewing the lower part of the siphon;
- removing and rotating the sink (to ensure normal access to the faucet mount);
- loosening the nut, which is located on the threaded rod;
- unscrewing the stud;
- removing the clamp;
- removal of all fasteners and plumbing fixtures with flexible leads (all elements are passed through the mounting hole).
For a job like changing a kitchen faucet, you can also use old hoses. They are disconnected from the faucet that has become unusable and screwed into the thread of the device being installed. The gasket on each hose is checked to ensure it is intact and in the correct place.
Mixer assembly
At the initial stage installation work you need to assemble a kitchen faucet. Its package should include flexible hoses and fasteners (round rubber gasket-ring, washer, rubber seal and 1-2 studs with nuts).
Flexible hoses are screwed into the tap to supply cold and hot water. Special attention Pay attention to the rubber cuffs on the liner fittings, which must not be damaged under any circumstances. It is recommended to moisten them slightly with water before use.
Further assembly of the mixer consists of the following steps:
- mounting pins are screwed into the lower part of the device;
- a rubber sealing ring is installed;
- The hoses are threaded into the holes in the sink.
Installation of a new mixer
In the kitchen, faucet installation can be done in two ways: in the sink or countertop. The first technology is more common. This is due to the fact that most kitchen sinks are produced with holes already made for the tap and water supply. And there is no need to additionally drill holes for the device.
With the second method, installing a mixer body in the kitchen is allowed only if the countertop is made of moisture-resistant material.
Installation in the sink
Installation of a plumbing fixture in a sink consists of the following steps:
- placing an annular gasket in the base of the mixer;
- laying flexible hoses into the mounting hole;
- fastening the rubber seal and the metal pressure plate (they have the same shape);
- screwing in threaded pins;
- final fixation of the tap using nuts screwed onto the pins.
The ring gasket at the base of the plumbing fixture performs a protective function. Thanks to the gasket, water will not leak under the sink.
During work, the outer coating of the device should be protected from mechanical damage. You can use electrical tape for this. If installation work is carried out correctly, the faucet will not move or rotate, and high-quality tightness of the joints will serve as the key to long-term operation of the mixer.
Countertop installation
This technology involves performing the following work:
- determining the location of the device;
- applying the mixer and marking the faucet sockets on the countertop;
- drilling holes with a drill;
- cutting out a hole in the table for the mixer;
- laying the sealing gasket;
- inserting the device into the hole made;
- fixing the mixer with a pressure washer.
When installed in a countertop close attention paid to the location of plumbing. A small distance to the sink can make it difficult to turn on (off) the valves, and too far away will cause water to get between the tap and the sink when weak pressure in system.
You can increase the service life of plumbing fixtures in the kitchen using rigid connection technology. This method provides the following algorithm of actions:
- an angled needle is screwed into the inlet hole of the faucet;
- a gasket is placed between the sink and the mixer;
- the tap is installed in the mounting hole;
- the lower part of the plumbing is sealed and sealed with a rubber gasket;
- a straight needle is screwed into the tap until it stops;
- the excess part of the pipe is cut off;
- the pipes are fixed using clamping couplings.
Depending on the type of fastener, installation of mixers is carried out using a nut or stud.
Breaking kitchen faucet can happen at the most inopportune moment, when there is simply no time to wait for a plumber to arrive. Agree, the ability to replace a plumbing fixture is useful to every home handyman. Moreover, you don’t need special skills or expensive tools to do the job.
Before you change the faucet in the kitchen, you need to understand its structure and have a clear idea of the procedure. We will help you in these matters.
The article provides detailed instructions for dismantling old devices and installing new models taking into account their design features. Having studied the material, you can easily cope with the work and save your family budget on calling a plumber.
The reasons for changing an appliance can be different, ranging from a decrease in its functionality due to wear of individual parts, and ending with replacement in order to adjust the mixer to the overall interior of the kitchen.
Regardless of the reason for the replacement, the process of dismantling and subsequent installation is almost monotonous. And the owner of the kitchen, first of all, needs...
The following parameters should be assessed:
- designer uniform;
- configuration;
- manufacturing material.
The design form is a choice at the personal discretion of the kitchen owner, but at the same time, when planning to change the appliance, it is advisable not to deviate from the overall picture of the kitchen interior. The mixer configuration must match the installation method.
Let us remind you that there are two common methods for installing kitchen faucets:
- wall;
- desktop
As a rule, in the kitchen, tabletop faucets are used, designed to be located on the panel of the utility sink or on the side of the sink. Wall-mounted ones are gradually going out of fashion or are used as part of luxury kitchen interiors.
For installation in the kitchen, faucets with two separate taps for regulating water flow or appliances with a lever-type mechanism are mainly used. The latest designs are considered more convenient and are quickly gaining popularity
Also, the owner of the kitchen who decides to change the plumbing is given the opportunity to choose from two types of devices according to the method of controlling the water flow. One type is a design with two taps (herringbone) and another type is where water is mixed with one lever.
The materials for the manufacture of mixing plumbing fixtures are usually silumin, brass, bronze, and ceramics. Devices based on silumin are less durable than brass and others.
Silumin mixers can be distinguished by weight and market price (they are lighter and cheaper). It is more practical to choose brass, bronze, ceramic products. Their price is more expensive, but they will last much longer, so in the long run such products look more economical.
Instructions for replacing the mixer
A detailed description of the steps to reinstall mixing equipment will help you avoid mistakes if you decide to replace it for the first time.
Tool and installation kit
Dismantling and installation of a traditional kitchen sink accessory is carried out using the following plumbing tools:
- adjustable wrench - gas wrench number one;
- wrenches (10*12, 13*14);
- socket wrench with deep stock (10*12, 13*14);
- wire brush,
- fluoroplastic tape – PTFE.
When solving the problem of how to replace or repair a faucet in the kitchen, the installer must have a complete installation set. This is a set of all the necessary elements: gaskets, connecting hoses, nuts, screws, washers, etc., which are usually sold along with the device.
The manufacturer supplements any kitchen faucet kit with instructions that outline the installation sequence of such a device.
To dismantle or install a faucet in the kitchen, you will need a small set of plumbing tools. Every owner in the house should have such a set. It will be useful not only for installation, but also during plumbing maintenance.
In addition to the installation tool, you will need household accessories: rags, bucket or basin. Thanks to these items, it is possible to minimize the spreading of water remaining in the pipelines when the dismantling process is carried out.
It is advisable to have a miniature flashlight, since usually replacing a tabletop kitchen faucet involves working in dark conditions - under the sink, under the sink.
Removing a kitchen faucet
The first step is to stop the supply of water (cold, hot) to the mixer - close the linear taps on the centralized supply pipes. After shutting off the lines, you need to open the mixer valves and make sure that no water flows. If there is a water leak, this indicates wear.
In this case, you will first have to replace the taps on the water supply lines and only then continue working in the kitchen.
Before starting work on dismantling/installing plumbing in the kitchen, it is necessary to block the water supply through the hot and cold lines. After turning off the shut-off valves, check the reliability of the blocking by opening the valves on the old mixer
If there is no water leakage, dismantling work can continue. Under the sink there are flexible connecting hoses (40-60 cm long) that must be removed.
The flexible line is attached to the centralized line with union nuts. It is convenient to unscrew them using an adjustable (gas) wrench. Flexible hoses are attached to the mixer body with tubular fittings. Here, to unscrew the fittings, you need a 13*14 or 10*12 wrench, depending on the modification.
After the flexible hoses are disconnected, it is time to dismantle the mixer itself. It is held on the sink thanks to two hex nuts and a special pressure washer.
The nuts are screwed onto two long studs about 50-60 mm long. Therefore, when replacing, it is most convenient to use a tubular socket wrench. The mounting assembly is located in the lower area of the faucet, so working under the sink is common practice in most cases.
When the screws are unscrewed, the support washer is removed from the studs, after which the mixer is easily removed.
When adding water to the kitchen for the first time, consider yourself very lucky. In this case, you can immediately do everything ergonomically and correctly - arrange comfortable access to the system and a “dry” way to replace equipment. When connecting to a ready-made network, there are also chances to not only install a faucet in the kitchen, but also install pipelines according to the above template. Today we will deal with both the first and second options.
You will be able to perform all the manipulations yourself, without the help of specialist plumbers. It will be two in one - you will acquire new skills and save your family budget.
Take into account
Security questions:
- Risk areas arise when water is supplied to the system at various connections, where rubber or rubberized products act as gaskets.
Advice: plan the installation of pipelines in such a way as to minimize the number of connections in the area between them.
- Installation of shut-off valves. Usually they are recommended to be installed on the main pipeline, and then to it.
Advice: a good rule of thumb is that each water distribution point must be equipped with a shut-off ball valve.
Then you have the opportunity, if necessary, to block the desired area without affecting the entire system.
- Plumbing equipment. How many times have they said that a low price is not your luck when purchasing, but usually quite the opposite. Inexpensive equipment and connecting hoses often have poor manufacturing quality, so they rarely last the warranty period.
Tip: one of the ways to choose the right mixer is to focus on the brand and customer reviews.
In both cases, operational reliability approaches 100%.
Preparation
We invite you to familiarize yourself with useful little things that will help you in further work. Ultimately, the final result will depend on them:
| Mixer | The main criteria should be added that the spout should be directed to the center of the sink. Pay attention to the complete set of the product, which includes flexible hoses and gaskets (rubber, silicone or paronite). Check the warranty mark in the instruction manual. |
| Nuts | When purchasing, pay attention to the diameter of the connecting nuts and couplings. The standard option is 1/2″, but if it is larger or you decide to connect the equipment directly to the main pipe, use an adapter. |
| Mixer socket | When the sink already has a hole for the tap, check that its diameter matches it. In its absence:
|
| Tool | You will need a minimum set - a screwdriver, pliers, 2 adjustable wrenches. We recommend stocking up on WD-40 lubricant, which will greatly facilitate the dismantling of old equipment. |
Start of the process
The instructions below will answer all questions related to installing a faucet on a kitchen sink. We recommend that you first cover the area of intended work with packing cardboard or other material so that metal parts, falling from a height, did not damage flooring or a cabinet. If possible, move the sink away from the wall.
Tip: if access to the mixer is possible only from one side, remove everything that will interfere with work.
This is usually a wastewater disposal system.
In the photo - shut-off valves will allow installation without shutting down the entire water supply system
Installation
The step-by-step work will look like this:
- Place the entire structure in the prepared nest. You can clearly see this in the package insert provided by the manufacturer.
So:
- Install a rubber gasket on the hole;
- place a metal base plate on top;
- insert the mixer itself;
- Place another gasket on the metal threaded stud from below;
- tighten everything with the fastening nut.
Tip: there are fasteners that do not have an internal rubber ring. Fixation is done manually without any tools. This should be written in the equipment assembly manual.
- Connect cold and hot water connections to your sockets. The clue will be the logo on the faucet lever, which has a “red” and “blue” half, respectively.
Tip: you can install the hoses before installing the mixer in the sink hole, this is not important.
- Take an adjustable wrench and connect each hose to its own line.
System startup and repair
Connection, as you can see, is not complicated, the main thing is to be careful in your work. All that remains is to make the first launch of the system, which will answer many questions.